GuidesLinkedIn ads

How to target the right people on LinkedIn Ads

LinkedIn Ads targeting works by combining filters in Campaign Manager: a required location, then company, job experience, demographic and interest attributes. Pick the fewest filters that describe your buyer, keep the audience large enough to deliver, and turn off the expansion options you did not choose.

Updated November 16, 20266 steps4 min read

Audit my LinkedIn ads →

$1 today. Cancel anytime before day 7.

Targeting setup order
  1. 1Set the locationChoose the countries or regions where the buyer works.
  2. 2Pick one buyer filterStart with job function plus seniority, or a company list.
  3. 3Add company filtersNarrow by industry or company size only if it matches the real buyer.
  4. 4Check audience sizeLook at the estimate and widen if it is too small.
  5. 5Review the settingsTurn off audience expansion and the Audience Network unless you want them.
  6. 6Exclude peopleRemove customers, employees and competitors.
On this page
  1. Start with the buyer, not the filter list
  2. Choose the filters that matter
  3. Keep the audience big enough to run
  4. Turn off the settings that quietly widen it
  5. Common targeting mistakes
  6. Layer on your own data
  7. Questions

Start with the buyer, not the filter list

Write down who signs, who uses and who influences, then pick which one the campaign speaks to. A campaign for a CFO and a campaign for a marketing manager are different audiences with different messages. Choosing both in one ad group means neither message lands.

Then choose the objective in Campaign Manager so the targeting step shows the right options. Awareness, consideration and conversion objectives all use the same audience tools, which are described on how to advertise on LinkedIn.

A simple test: describe the buyer in one sentence without using the word “and”. If you cannot, you have two audiences.

Choose the filters that matter

Location is required. After that, the main groups are company (name, industry, size, growth), job experience (title, function, seniority, skills, years of experience), demographics and interests. Within one filter group, selections combine as “or”. Between groups, they combine as “and”, so every added group narrows the audience.

Job function and seniority are usually safer than job title. Titles are free text, so people write them in many ways, and LinkedIn’s standard titles do not always match how your buyers describe themselves. A few tested title lists inside a function-based audience often do best.

Skills and group targeting exist, but they rely on what members chose to list. Use them to find a niche that titles cannot describe, such as a specific tool, and test them against a function-based audience before committing budget.

Company size is a useful filter for software, since a ten-person company and a ten-thousand-person one buy very differently. Pick the bands your best customers fall in rather than ticking all of them.

Want this checked in your LinkedIn account?

Reads campaigns, audiences, lead forms and conversions. Every change waits for your approval.

Keep the audience big enough to run

Campaign Manager shows an audience size estimate on the right. A very small audience will not deliver, and a very large one dilutes the message. As a rule of thumb, LinkedIn suggests tens of thousands of members for feed campaigns, with a lower floor for message formats. Treat it as a guide and check the estimate on screen.

If the number is too small, remove the least important filter rather than all of them. Dropping seniority is usually safer than dropping function. If it is too large, add an industry or company size filter that matches your real customers.

If you are unsure, run two ad groups with different audience sizes and the same ad. The cost per result tells you whether the tighter audience is worth its higher CPM. LinkedIn is expensive per impression, so a small cost advantage from sharper targeting adds up quickly.

Turn off the settings that quietly widen it

LinkedIn offers audience expansion and a partner placement option called the LinkedIn Audience Network. Both can raise reach and lower the quality of the match. Neither is wrong, but they should be a choice, not a default you did not notice. Test them one at a time against a clean control.

Also set exclusions. Remove your current customers, your employees and any competitor lists you have. The exclusion list is one of the cheapest ways to stop waste, and it takes five minutes.

Check where else ads can show. Placement options can include partner sites, and the quality of those clicks is often lower than in the feed. Read the placement report after two weeks and keep only what produces leads.

Common targeting mistakes

The most common mistake is stacking filters until the audience is a few thousand people. Each extra filter feels like added precision, but the campaign then cannot spend, and the few people it reaches see the ad too often. Add filters one at a time and watch the size estimate after each.

The second is mixing buyer types in one campaign. A single ad group aimed at both executives and practitioners forces generic copy. Split them, give each its own message, and compare cost per lead between them.

The third is trusting job title text blindly. A title like “growth” can mean marketing, sales or product depending on the company. Check a sample of the people you reach in your own CRM data before you scale, and use the website demographics report from your tag to see who actually visits.

Layer on your own data

The strongest audiences use first-party data: a company list for account-based work, a contact list, or website visitors. These live under matched audiences, and the how-to is on LinkedIn matched audiences. For named accounts, follow LinkedIn ABM campaign.

The part you can hand off: Sprites reads your LinkedIn Ads account, can propose matched and predictive audiences and budgets as approval cards you edit and approve, and reports on which audiences produce leads.

Questions

What targeting options does LinkedIn Ads offer?

Location, company attributes, job experience such as title, function and seniority, demographics, education, interests, and your own audiences from lists, website visits and engagement.

How big should a LinkedIn audience be?

Big enough that the campaign can spend without hammering the same people. As a rule of thumb, feed campaigns want tens of thousands of members, and Campaign Manager shows an estimate as you build.

Should I target by job title or job function?

Function plus seniority is more reliable because titles vary. Use titles as a second layer when a specific role matters.

Can I target a list of companies?

Yes. Upload a company list as a matched audience and layer job function or seniority on top.

Keep going

Have Sprites do this in LinkedIn Campaign Manager

  • Reads campaigns, audiences, lead forms and conversions
  • Drafts targeting, budgets and ads as cards
  • Every change waits for your approval