GuidesMeta ads

How to fix a Facebook ad that is not spending

A Facebook ad that is not spending is blocked by one of five things: the account or payment, the ad’s review status, the schedule, an audience that is too small, or a budget and bid that cannot win auctions. Check them in that order, starting with the Delivery column in Ads Manager, which usually names the cause.

Updated November 16, 20265 steps5 min read

Audit my Meta ads →

$1 today. Cancel anytime before day 7.

A fixed order of checks
  1. 1Read the Delivery columnIt shows the status at the campaign, ad set, and ad level.
  2. 2Check account and paymentA restriction, failed payment, or spending limit stops everything.
  3. 3Check review and scheduleAds in review or with a future start date will not spend.
  4. 4Check audience sizeToo narrow or overlapping audiences starve delivery.
  5. 5Check budget and bidA low cap or tight bid control may lose every auction.
On this page
  1. Start with the Delivery column
  2. Rule out account and payment problems
  3. Check review status and the schedule
  4. Audience, overlap, and learning
  5. Worked examples of the usual causes
  6. Budget, bid controls, and competition
  7. Questions

Start with the Delivery column

In Ads Manager, look at the Delivery column for the campaign, ad set, and ad. It shows states such as Active, In review, Learning, Learning limited, Not delivering, or Rejected, and for problems it often gives a reason. Check all three levels, because an ad set can be active while its only ad is rejected, or a campaign can be paused above them.

Also check the toggles on the left. A paused parent switches off everything below it. It sounds obvious, and it is the cause more often than people admit, especially after duplicating campaigns.

Rule out account and payment problems

If the ad account has no valid payment method, a failed payment, or has hit its account spending limit, ads cannot deliver. Open Billing and check for failed charges, a payment threshold that has not been met, or a limit that has been reached. Also check that the Page the ad runs from is published and not restricted.

An ad account can also be restricted or disabled for a policy reason. That shows as an account-level notice in Ads Manager and in Account quality. If it does, work through Facebook ad account restricted before you change anything else.

Want this checked in your Meta account?

Reads your campaigns, ad sets, ads and pixel health. Every change waits for your approval.

Check review status and the schedule

New and edited ads go through review. Most clear within a day, but if an ad is still “In review,” it will not spend. If it was rejected, the notice explains which policy and what to change; fix it and request a review. Repeated rejections of the same kind affect the account, so address the cause, not just that ad.

Check the schedule too. If the ad set has a start date in the future, an end date in the past, or an ad schedule that limits it to certain hours, spend will be lower or zero. A lifetime budget with a schedule can also pace slowly at the start of the period.

Audience, overlap, and learning

An audience that is too narrow, such as a small radius combined with tight interests and a custom audience exclusion, may have nobody left to show the ad to. Widen it and see whether delivery picks up. If several ad sets target the same people, they compete with each other in the auction, and some will under-deliver. Consolidate overlapping ad sets.

Ad sets with too little volume get stuck in “Learning limited,” which is a symptom, not a cause: the budget is too low for the number of results you ask for. See the learning phase for how to size it. Also check that the creative is allowed in the placements you selected.

Worked examples of the usual causes

A new campaign shows Active but spends nothing. The Delivery column on the ad says In review, and it was submitted late the night before. Nothing to fix: wait for review, and check again the next morning. If it has been two days, request another review or look for a notice in Account quality.

An ad set that spent well last month now spends a fraction. Nothing in the account changed, but the cost cap was set when costs were lower, and a seasonal rise pushed the auction price past it. Raising the cap, or switching to the highest volume bid strategy for a few days, brings delivery back and tells you how much the cap was holding back.

A campaign with three ad sets spends on one and starves the other two. With campaign budget optimization on, Meta moves budget to whatever it expects to perform, which can leave an ad set with almost nothing. If you need each audience to get a share, set minimum spend limits or use ad set budgets. Check this before you decide that an audience does not work, because it may simply never have been given a chance to prove itself.

Budget, bid controls, and competition

A budget that is smaller than the cost of one result may deliver in fits and starts. If you set a cost cap or bid cap, a value that is lower than the auction price means you lose every auction and spend little. Try raising or removing it as a test. During crowded periods, such as the lead-up to major sales, costs rise and a cap that worked in March can stop spending in November.

Under-delivery that has no other cause often comes down to the ad losing auctions on quality: low expected engagement, or a creative that people hide or ignore. Refresh the creative. For more on what drives costs, see high CPM on Facebook ads and Facebook ads cost.

The part you can hand off: Sprites can check your Meta account for the stalled-delivery causes above, such as rejected ads, paused parents, small audiences, and tight caps, and propose fixes as approval cards you approve before anything changes.

Questions

Why is my Facebook ad active but not spending?

The ad may be in review, scheduled for later, limited by a tight audience, or losing auctions because of a low budget or bid cap. Check the Delivery column and the parent campaign and ad set before changing the budget.

How long does it take for a Facebook ad to start spending?

Review usually takes up to a day, and sometimes longer. After approval, spending typically begins within hours, though a new ad set may pace slowly while it learns.

Does a low budget stop Facebook ads from spending?

It can. If the daily budget is lower than what one result costs in your market, delivery will be uneven. Raise the budget, or optimize for a cheaper event, so the system gets enough signal.

What does “Learning limited” mean?

It means the ad set is not getting enough optimization events to exit the learning phase. Raise the budget, widen the audience, or consolidate ad sets so results arrive faster.

Keep going

Have Sprites do this in your Meta account

  • Reads your campaigns, ad sets, ads and pixel health
  • Drafts budget, audience and creative changes as cards
  • Every change waits for your approval